Setup Devices

From Taridium

Revision as of 20:06, 27 October 2009 by Webmaster (Talk | contribs)
Jump to: navigation, search

ipbx supports the following devices for auto-provisioning. Any other type of device needs to be setup manually and possibly requires console modifications. If you have a device type with which you need help, please contact Taridium or your authorized reseller. Check the How To section for examples of manual setups for unsupported phone types.

To access auto-provisioning settings click on ConfigurationAdvanced SetupDevices.

Click on the approriate configure button to enable auto-provisioning for your selected brand. This procedure might take a couple of minutes depending on the provisioning method.

Warning.gif Please take the appropriate precautions when exposing any of the provisioning services to the internet!


Contents

Aastra

Semi Automated Setup

In case you don't have your network configured for automatic provisioning, or if you want configure your phone at a remote location, you can still use the configuration system by telling the phone where to look for the its configuration.

Press the Settings button, sometimes labeled Options or a wrench symbol and scroll Down to 3. Phone Status and select it. You should now see the 1. IP&MAC Addresses option, select it and note the IP address.

  1. Enter this IP address into your web browser's address bar. E.g. http://192.168.12.33.
  2. Enter the default username admin and password 22222.
  3. Click on the Advanced SettingsConfiguration Server at the bottom of the menu.
  4. Select HTTP as Download Protocol.
  5. Enter your ipbx IP address into the HTTP Server field.
  6. Enter prov into the HTTP Path field.
  7. Click on Save Settings.
  8. Click on OperationReset.
  9. Click on Restart Phone.

The phone will reboot shortly and attempt to retrieve the configuration file from your ipbx system.

Cisco

Standard provisioning currently only support non-XML configuration files. This excludes Cisco Unified IP Phone 7965G, 7970G and others.

Linksys SPA Phones and ATA's

(formerly also known as Sipura)

Cisco/Linksys phones are meant to be provisioned by HTTP, but might initially only pick up the default pre-provisioning file from the TFTP server (default behavior of factory phones). This requires a second reboot.

  1. Initial boot: Phone or ATA picks up init.cfg file with instructions to use the HTTP profile
  2. Second boot: Phone/ATA picks up it's actual configuration file.

Contents of Pre Provisioning File

 <flat-profile>  
 
   <Profile_Rule ua="na">http://%%eth0%%/prov/spa$MAU.cfg
   </Profile_Rule>
 
 </flat-profile>


Where %%eth0%% is the variable which will automatically be replaced with the IP address of your ipbx system.

You can easily reboot your Linksys ATA or phone by entering the following URL into your webbrowser:

 http://[ip address]/admin/reboot

or

 http://[ip address]/admin/reset

Semi Automated Setup

In case you don't have your network configured for automatic provisioning, or if you want configure your phone at a remote location, you can still use the configuration system by telling the phone where to look for the its configuration.

Press the Setup button (this button looks like a page symbol) and scroll Down to Network and select it. You should now see the Current IP information. On ATA's that don't have an interface, connect a phone to telephone port 1 and dial **** (four asterisks) Then dial: 110 # - This will cause the the ATA to readback the IP address acquired via DHCP.

  1. Enter this IP address into your web browser's address bar. E.g. http://192.168.12.33.
  2. Click on the Admin Login link on the right hand side. The default configuration will require no password.
  3. Click on the advanced link on the right hand side. This will expose further configuration options.
  4. Click on the 'Provisioning' Tab
  5. Enter The following 'Profile Rule' : http://[ip address of pbx]/prov/spa$MAU.cfg
  6. Click on 'Submit All Changes' at the bottom of the page.
  7. Reboot your phone or enter http://[ip address of phone]/admin/resync

The phone will reboot shortly and attempt to retrieve the configuration file.

Polycom

Semi Automated Setup

In case you don't have your network configured for automatic provisioning, or if you want configure your phone at a remote location, you can still use the configuration system by telling the phone where to look for the its configuration.

Polycom phones need to setup directly on the phone for semi-automated provisioning:

  1. Press the Menu key.
  2. Select Settings.
  3. Select Advanced.
  4. Enter in your admin password to the phone (456). Hit the Enter soft key.
  5. Select Admin Settings.
  6. Select Network Configuration.
  7. Select Server Menu.
  8. Enter the IP address of your ipbx system.
  9. Hit the Exit Soft key until you can select Save Config
  10. Reboot your phone

Resetting your Polycom Phone

Reset Local Config

  1. Press the Menu key.
  2. Select Settings.
  3. Select Advanced.
  4. Enter in your admin password to the phone (456). Hit the Enter soft key.
  5. Select Admin Settings.
  6. Select Reset to Default.
  7. Select Reset Local Config.

Reset Device Settings

IP 30x: Hold down the 4, 6, 8 and * keys simultaneously.
IP 430: Hold down the 1, 3, 5 and 7 keys simultaneously.
IP 50x: Hold down the 4, 6, 8 and * keys simultaneously.
IP 60x: Hold down the 4, 6, 8 and * keys simultaneously.

NOTE: This method will require the Administrator Password(456)

Snom

XML Applications

For supported XML applications and phones see Phone Browser XML Applications.

Personal tools
Namespaces
Variants
Actions
Toolbox