Advanced Setup: Configuration

From Taridium

Revision as of 16:38, 29 June 2011 by Webmaster (Talk | contribs)
Jump to: navigation, search

Contents

System Setup

To perform the basic system setup, go to ConfigurationAdvanced Setup. Make sure to set your system name and primary IP address.

System Name

It is advisable to identify your system with a simple name. This will optionally be displayed on both administrator and user panels (display in header)

ipbx IP Address

This is the IP address or fully qualified domain name of your PBX server. If you have a public IP address assigned or port forwarding enabled, use your external IP address. Note that you might need to adjust your IP address in the SIP and/or IAX configurations (General Settings) separately.

Default Landing

The default landing option specifies whether visitors are sent to the administrator interface or the End User Panel when accessing the webserver root.

End User Panel

The End User Panel settings control access and features for the End User Interface. The end user interface can be accessed via http://myipaddress/user, where myipaddress is your server. Some features might only be available if the appropriate module has been registered.

Voicemail

Display Voicemail PIN's in plain text will display Voicemail PIN's in plain text in the administrator interface. See SystemVoicemailMailboxes.

Default PIN Mode When creating users, ipbx will automatically assign Voicemail PIN's to users. These can be either the same as the mailbox number or a random 4 digit number. See SystemVoicemailMailboxes.

Trunks

This interaction configures general options for trunk calls. Force ringback tone on trunk calls will cause outbound calls to always signal a ringing state, even if the remote end does not provide it. Only enable this if you have problems with getting proper ringback signalling from the far end.

Click to Call

The Play back connection announcement will enable the playback of a connecting announcement when using click to call features in the End User Panel and URL Control API.

The Auto Answer caller phone will cause the first leg to automatically answer if supported by your phone. Commonly supported phones include, Aastra, Polycom and Linksys. Note that some phones such as Polycom SoundPoint IP need to be configured used ipbx's automatic provisioning

International Calling Prefix

The international calling prefix is used whenever there is need to ID an international call. The default value of 00,011 will cover the US and most European countries. If you are using multiple prefices, make sure they aren't ambiguous (e.g. 00,0011). If you are using a outside dialing prefix such as 0 or 9, enter your international prefix as such, 000 or 9011 etc. The prefix is always taken into account BEFORE any transformations are applied. See also Transformations.

Conferencing

This interaction configures general options for 'meetme' style conferencing. The following options can set for announcing callers:

See also Conferencing for conferencing settings pertaining to ipbx 2.3 and higher.

SIP Subscriptions

Automatic Hint Management allows you to control the automatic generation of SIP dialplan hints. This is required for busy lamp field (BLF) features on many phones.

Caller ID

Name

The system Default Caller ID number and name will be used whenever there is no preset default caller ID. If you want to present this caller ID to the far end regardless of whether the call was forwarded check also apply on forwarded calls. Note that some providers will override caller ID settings that

If your provider does not accept caller ID name setting check don't send caller ID name on outbound calls. This is quite common on Voice T1's or E1's (PRI).

Number

This interaction configures how caller ID on outbound calls (trunk calls) is handled.

Hardware Interface

Which hardware interface naming system you intend to use. Zaptel is the deprecated name for Digium's DAHDI interface and should only be used in circumstances where older hardware drivers are required.

Additional Line Templates

If you are using the Additional Line/Softphone Module you can select a template that will be used to create the additional user line. Both SIP and IAX types are supported.

DHCP Settings

Hardware Interface

This setting allows you to select which hardware interface you wish to use.

CDR Maintenance

The CDR Maintenance allows you to set an automated deletion schedule for your call records. Keep in mind that call logs can grow very big over time.

Queue Log Maintenance

he CDR Maintenance allows you to set an automated deletion schedule for your queue logs. Keep in mind that queue logs can grow very big over time.

Personal tools
Namespaces
Variants
Actions
Toolbox