Initial Configuration

From Taridium

(Difference between revisions)
Jump to: navigation, search
m (Changing the admin Password)
(Accessing ipbx)
Line 7: Line 7:
== Accessing ipbx ==
== Accessing ipbx ==
 +
 +
You might need to adjust your network configuration before you are able to access your PBX system. The default shipping status for most ipbx systems is a DHCP network configuration. If you need to change this and aren't able to put your PBX on DHCP network please proceed as follows:
 +
 +
1. Connect your PBX to the network (ethernet port labeled ETH 0 or 0 on ipbx SRV-1, SRV-2 and SRV-3 servers)
 +
 +
2. Connect your monitor and keyboard or KVM unit.
 +
 +
3. Power up your system. On SRV-2 servers press the small button on the left front side. You might need to use a pen or other pointy object.
 +
 +
4. Wait for a complete power-up and login as '''root''' using the default password '''taridium200'''.
 +
 +
5. Edit the system network configuration
 +
[root~]# nano /etc/sysconfig/network-scripts/ifcfg-eth0
 +
 +
and modify the entries using this template:
 +
 +
DEVICE=eth0
 +
BOOTPROTO=none            <---- Change to none
 +
BROADCAST=x.x.x.x  <---- Update according to your config
 +
HWADDR=00:30:48:43:D7:9C
 +
IPADDR=x.x.x.x            <---- Update according to your config
 +
NETMASK=x.x.x.x    <---- Update according to your config
 +
NETWORK=x.x.x.x    <---- Update according to your config
 +
ONBOOT=yes
 +
GATEWAY=x.x.x.x    <---- Update according to your config
 +
TYPE=Ethernet
 +
 +
DO NOT COPY the information above, just use it as a reference.
 +
 +
you can save by pressing CTRL-O (output) and quit via CTRL-X
 +
 +
Enter:
 +
 +
6. [root~]# nano service network restart
To access the administrator interface connect to your PBX via http or https e.g. http://192.168.21.1/ You will be prompted for username and password. The superuser is '''admin''' and the default password is '''taridium200''' - change these immediately to prevent unauthorized access.  
To access the administrator interface connect to your PBX via http or https e.g. http://192.168.21.1/ You will be prompted for username and password. The superuser is '''admin''' and the default password is '''taridium200''' - change these immediately to prevent unauthorized access.  

Revision as of 22:07, 27 April 2009

This section describes a standard business telephone system deployment.

Contents

Pre-requisites

Accessing ipbx

You might need to adjust your network configuration before you are able to access your PBX system. The default shipping status for most ipbx systems is a DHCP network configuration. If you need to change this and aren't able to put your PBX on DHCP network please proceed as follows:

1. Connect your PBX to the network (ethernet port labeled ETH 0 or 0 on ipbx SRV-1, SRV-2 and SRV-3 servers)

2. Connect your monitor and keyboard or KVM unit.

3. Power up your system. On SRV-2 servers press the small button on the left front side. You might need to use a pen or other pointy object.

4. Wait for a complete power-up and login as root using the default password taridium200.

5. Edit the system network configuration [root~]# nano /etc/sysconfig/network-scripts/ifcfg-eth0

and modify the entries using this template:

DEVICE=eth0 BOOTPROTO=none <---- Change to none BROADCAST=x.x.x.x <---- Update according to your config HWADDR=00:30:48:43:D7:9C IPADDR=x.x.x.x <---- Update according to your config NETMASK=x.x.x.x <---- Update according to your config NETWORK=x.x.x.x <---- Update according to your config ONBOOT=yes GATEWAY=x.x.x.x <---- Update according to your config TYPE=Ethernet

DO NOT COPY the information above, just use it as a reference.

you can save by pressing CTRL-O (output) and quit via CTRL-X

Enter:

6. [root~]# nano service network restart

To access the administrator interface connect to your PBX via http or https e.g. http://192.168.21.1/ You will be prompted for username and password. The superuser is admin and the default password is taridium200 - change these immediately to prevent unauthorized access.

Changing the admin Password

To change the administrator's password Click on: ConfigurationAccess ControlAdministrator Password. Optionally you can limit access from a specific network only. Be careful when changing this as you might lock yourself out of the system. See also How to reset the administrator password

Next Steps

Personal tools
Namespaces
Variants
Actions
Toolbox