Bandwidth.com

From Taridium

(Difference between revisions)
Jump to: navigation, search
(Completely installed ipbx system)
(Completely installed ipbx system)
Line 7: Line 7:
===Completely installed ipbx system===
===Completely installed ipbx system===
-
If you have obtained your ipbx system directly from Taridium and have a valid maintenance or managed VoIP service contract, you can ask Taridium to perform this configuration for you. In order for you to configure your trunk you should have your phones, IVRs, call groups, queues etc. already setup. See [[Installing_ipbx|Installing ipbx]] and [[Configuring ipbx]]
+
If you have obtained your ipbx system directly from Taridium and have a valid maintenance or managed VoIP service contract, you can ask Taridium to perform this configuration for you. In order for you to configure your trunk you should have your phones, IVRs, call groups, queues etc. already setup. See [[Installing_ipbx|Installing ipbx]] and Initial_Configuration|Initial Configuration]].
===Version Note===
===Version Note===

Revision as of 15:33, 25 February 2009

Bandwidth.gif

This page describes how to configure your Taridium ipbx system with Bandwidth.com SIP Trunking Service.

Contents

Prerequisites

Completely installed ipbx system

If you have obtained your ipbx system directly from Taridium and have a valid maintenance or managed VoIP service contract, you can ask Taridium to perform this configuration for you. In order for you to configure your trunk you should have your phones, IVRs, call groups, queues etc. already setup. See Installing ipbx and Initial_Configuration|Initial Configuration]].

Version Note

Warning.gif Bandwidth.com trunks require ipbx v. 2.0.1 or higher for proper operation.

SIP trunking information provided by Bandwidth.com

Trunk Configuration

Navigate and login to the ipbx administrator interface (you will need admin class permissions). E.g.

http://[ip address of your pbx]/ipbx/

Click on ConfigurationVoIP Trunksadd SIP Trunk

Enter the following details:

  1. Trunk Name → bandwidth-1
  2. Type → friend
  3. Host → 216.82.225.202
  4. Context → incoming (default)
  5. Can Re-Invite → no
  6. Insecure → very
  7. Disallow → all (enter or select all)
  8. Allow → ulaw (enter or select ulaw)

Leave all other configuration details as per default.

Bw-trunk.gif

Click on add trunk to add your trunk to the configuration.

Click on ConfigurationRoutingOutbound Routing

Enter your destination patterns and select the newly created SIP/bandwidth-1 trunk to terminate your calls.

Examples destination pattern:

_+ZXXXXXX. This will accept any numbers that match the E.164 pattern and send them to bandwidth.com

Bw-outbound.gif

Transformation Configuration

Since bandwidth.com requires numbers to be dialed as fully qualified E.164 numbers you will need to add number transformations before sending your calls out.

Click on ConfigurationRoutingTransformations

Add a new rule of type before outbound routing with Pattern _1NXXNXXXXXX and Output +${EXTEN} - This rule will transform any North American numbers to E.164.

Add a new rule of type before outbound routing with Pattern _011ZXXXXX. and Output +${EXTEN:3} - This rule will transform any international prefix numbers to an E.164 pattern.

Bw-transform.gif

If desired you can also add inbound transformations before inbound routing which for example could strip the + sign for further matching in your inbound routes.

DID Configuration

In order for ipbx to know about your DIDs, you will have to add inbound routes:

Click on ConfigurationRoutingInbound Routing

Bw-inbound.gif

Enter your DIDs as specified by bandwidth.com e.g. +12125552200 and select a local destination for your DID.

Personal tools
Namespaces
Variants
Actions
Toolbox